Articles: Cooling
 

Bookmark and Share

(3) 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 ]

Testbed and Methods

We are going to test the cooling efficiency of Alpenföhn Nordwand inside a closed system case with the following configuration:

  • Mainboard: ASUS P6T Deluxe (Intel X58 Express), LGA 1366, BIOS 1702;
  • Chipset cooler: Scythe Mini Kaze 50 mm (1000 RPM);
  • Processor: Intel Core i7-920, 2.67 GHz, 1.25 V, 4 x 256 KB L2, 8MB L3 (Bloomfield, C0);
  • Thermal interface: Tuniq TX-2;
  • Graphics card: XFX Radeon HD 5750 1 GB GDDR5, 700/4600  MHz;
  • Memory: DDR3 3 x 2 GB OCZ Platinum Low-Voltage Triple Channel (Spec: 1600 MHz / 7-7-7-24 / 1.65 V);
  • System HDD: Western Digital VelociRaptor (SATA-II, 300 GB storage capacity, 10,000 RPM, 16 MB cache, NCQ) inside Scythe Quiet Drive 3.5” silencer and cooler chassis;
  • System case: Antec Twelve Hundred (front panel: two Noiseblocker NB-Multiframe S-Series MF12-S1 fans at 900 RPM and Scythe Gentle Typhoon fan at 900 RPM; back panel: two Scythe SlipStream 120 fans at 900 RPM; top panel: standard 200 mm fan at 400 RPM);
  • Control and monitoring panel: Zalman ZM-MFC2;
  • Power supply: Zalman ZM1000-HP 1000 W (with a default 140 mm fan).

During this test session we managed to overclock our 45nm quad-core processor (with polished heat-spreader) with the multiplier set at 21x and “Load-Line Calibration” enabled to 4.01 GHz. The nominal processor Vcore was increased to 1.3625 V in the mainboard BIOS.

The memory voltage was at 1.64 V and its frequency was around 1.55 GHz (7-7-7-14_1T timings). All other parameters available in the mainboard BIOS and connected with CPU or memory overclocking remained unchanged (set to Auto).

All tests were performed under Windows 7 RTM x64 operating system. We used the following software during our test session:

  • Linpack 64-bit with LinX shell version 0.6.4 – to create maximum CPU load (two test cycles, 5 Linpack runs in each cycle with 3584 MB RAM capacity involved);
  • CPU-Z 1.52.2 – to monitor processor core voltage and frequency;
  • Real Temp 3.46 beta – to monitor the processor core temperature;
  • RivaTuner 2.25 alpha build 9 – for visual control over temperature changes (with RTCore plagin);
  • Everest 5.30.1954 beta – to monitor default fans rotation speeds.

So, the complete screenshot during the test session looks as follows:

The CPU was loaded with two consecutive Linpack test runs with the settings as indicated above. The stabilization period for the CPU temperature between the two test cycles was about 8-10 minutes. We took the maximum temperature of the hottest processor core of the four for the results charts. The ambient temperature was checked next to the system case with an electronic thermometer with 0.1 °C precision that allows monitoring the temperature changes over the past 6 hours. During our test session room temperature was at 23.6-24.0 °C.

All super-coolers will now be compared against the leading air-cooling solution Noctua NH-D14. Besides it, the best cooler with direct touch technology, the Thor’s Hammer from Xigmatek, is included into the comparison.

 

Besides its default fan, the Alpenföhn Nordwand was tested with one and two Thermalright TR-FDB-2000 fans working quietly at 1050 RPM as well as at a full speed of 2040 RPM (one fan for intake and another for exhaust). The other two coolers were tested with the same fans.

 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 ]

Discussion

Comments currently: 3
Discussion started: 12/09/09 01:11:40 AM
Latest comment: 01/02/10 11:10:42 AM

View comments

Add your Comment