Articles: Cooling
 

Bookmark and Share

(2) 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 ]

Testbed and Methods

Cooler Master Hyper Z600 cooler and its today’s competitor were tested in two modes: in an open testbed when the mainboard sits horizontally on the desk and the cooler is installed vertically, and in a closed testbed with the mainboard in vertical position.

Our testbed remained the same throughout the entire test session and featured the following configuration:

  • Mainboard: ASUSTek P5K Deluxe/WiFi-AP (Intel P35), LGA 775, BIOS 0812
  • Processor: Intel Core 2 Extreme QX9650 (3.0GHz, 1.25V, 2x6MB L2 cache, 4x333MHz FSB, Yorkfield, C0)
  • Thermal interface: Arctic Silver 5
  • Graphics card: Chaintech GeForce 9800 GTX GDDR3 512MB / 256bit, 675/2200MHz
  • Memory:
    • 2 x 1024MB DDR2 Corsair Dominator TWIN2X2048-9136C5D (1142MHz / 5-5-5-18 / 2.1V);
    • 2 x 1024MB DDR2 CSXO-XAC-1200-2GB-KIT DIABLO (1200MHz / 5-5-5-16 / 2.4V).
  • Disk subsystem: Samsung HD501LJ (SATA-II, 500GB storage capacity, 7200rpm, 16MB cache, NCQ)
  • Optical drive: Samsung SH-S183L SATA-II DVD RAM & DVD±R/RW & CD±RW
  • System case: System case: ASUS ASCOT 6AR2-B Black&Silver (ATX) with 120mm ~960RPM Scythe Slip Stream fans for air intake and exhaust (the fans are installed on silicon spindles), and the same 120mm ~840RPM fan on the side panel
  • Control and monitoring panel: Zalman ZM-MFC2
  • Power supply: Enermax Galaxy EGA1000EWL 1000W (a default 135mm fan for intake; and 80mm fan for air exhaust)

All tests were performed under Windows XP Professional Edition SP2. SpeedFan 4.34 Beta 44 was used to monitor the temperature of the CPU, reading it directly from the CPU core sensor:

The mainboard’s automatic fan speed management feature was disabled for the time of the tests in the mainboard BIOS. The CPU thermal throttling was controlled with the RightMark CPU Clock Utility version 2.35.0:

The CPU was heated up with OCCT (OverClock Checking Tool) version 2.0.0a in a 23-minute test with maximum CPU utilization, during which the system remained idle in the first 1 and last 4 minutes of the test:

I performed at least two cycles of tests and waited for approximately 20 minutes for the temperature inside the system case to stabilize during each test cycle. The stabilization period in an open testbed took about half the time. The maximum temperature of the hottest CPU core of the four in the two test cycles was considered the final result (if the difference was no bigger than 1°C – otherwise the test was performed at least once again). Despite the stabilization period, the result of the second test cycle was usually 0.5-1°C higher.

The ambient temperature was checked next to the system case with an electronic thermometer that allows monitoring the temperature changes over the past 6 hours. During our test session room temperatures varied between 21 ~ 21.5°C. It is used as a staring point on the diagrams. Note that the fan rotation speeds as shown in the diagrams are the average readings reported by SpeedFan, and not the official claimed fan specifications.

The noise level of each cooler was measured according to our traditional method described in the previous articles with the help of an electronic noise meter – CENTER-321. The subjectively comfortable noise level was considered 34.5dBA and is marked with a dotted line in the diagram. The ambient noise from the system case without the CPU cooler didn’t exceed 32.5dBA when measured at 1m distance.

We decided to compare the performance of our today’s hero – Cooler Master Hyper Z600 - against that of ZEROtherm NV120 Premium cooler:

We tested this cooler in two modes: with the fan rotating at ~1320RPM with moderate noise and at pretty noisy maximum fan rotation speed of ~2760RPM. Cooler Master Hyper Z600 was tested not only in passive mode, but also with one and then with two Scythe SlipStream 120 fans working at ~900RPM and ~2000RPM. Two fans were attached at the opposite sides of the heatsink for air intake/exhaust.

 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 ]

Discussion

Comments currently: 2
Discussion started: 06/01/08 07:02:56 AM
Latest comment: 06/01/08 03:48:08 PM

View comments

Add your Comment