Articles: Cooling
 

Bookmark and Share

(10) 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 ]

Testbed and Methods

All tests of the new Noctua cooler and its only competitor were performed in a testbed with the following configuration:

  • Mainboard: ASUS P6T Deluxe (Intel X58 Express), LGA 1366, BIOS 1702;
  • Processor: Intel Core i7-920, 2.67 GHz, 1.25V, 4 x 256 KB L2, 8MB L3 (Bloomfield, C0);
  • Thermal interface: Tuniq TX-2;
  • Graphics card: XFX Radeon HD 5750 1 GB GDDR5, 700/4600 MHz;
  • Memory: DDR3 PC3-12800 3 x 2 GB OCZ Platinum Low-Voltage Triple Channel (Spec: 1600MHz / 7-7-7-24 / 1.65 V);
  • System HDD: Western Digital VelociRaptor (SATA-II, 300 GB storage capacity, 10,000 RPM, 16 MB cache, NCQ) inside Scythe Quiet Drive 3.5” silencer and cooler chassis;
  • System case: Antec Twelve Hundred (front panel: two Noiseblocker NB-Multiframe S-Series MF12-S1 fans at 900 RPM and Scythe Gentle Typhoon fan at 900 RPM; back panel: two Scythe SlipStream 120 fans at 900 RPM; top panel: standard 200 mm fan at 400 RPM; side panel removed);
  • Control and monitoring panel: Zalman ZM-MFC2;
  • Power supply: Zalman ZM1000-HP 1000 W (with a default 140 mm fan).

During this test session we managed to overclock our 45nm quad-core processor (with polished heat-spreader) with the multiplier set at 21x and “Load-Line Calibration” enabled to 4.01 GHz. The nominal processor Vcore was increased to 1.36875 V in the mainboard BIOS.

The memory voltage was at 1.64 V and its frequency was around 1.55 GHz (7-7-7-14_1T timings). All other parameters available in the mainboard BIOS and connected with CPU or memory overclocking remained unchanged (set to Auto).

All tests were performed under Windows 7 RTM x64 operating system. We used the following software during our test session:

  • Linpack 64-bit with LinX shell version 0.6.4 – to create maximum CPU load (two test cycles, 5 Linpack runs in each cycle with 3584 MB RAM capacity involved);
  • CPU-Z 1.52.2 – to monitor processor core voltage and frequency;
  • Real Temp 3.42 – to monitor the processor core temperature;
  • Everest 5.02.1925b – to monitor fans rotation speeds.

So, the complete screenshot during the test session looks as follows:

The CPU was loaded with two consecutive Linpack test runs with the settings as indicated above. The stabilization period for the CPU temperature between the two test cycles was about 8-10 minutes. We took the maximum temperature of the hottest processor core of the four for the results charts. The ambient temperature was checked next to the system case with an electronic thermometer with 0.1 °C precision that allows monitoring the temperature changes over the past 6 hours. During our test session room temperature was at 23.6-24.0 °C.

Our cooler, Noctua NH-D14, will be competing against Thermalright IFX-14. Both solutions were tested with Noctua’s default fans:

Besides, we also added the third fan - Thermalright TR-FDB-2000. We also tested both coolers with two Thermalright fans in quiet mode at 810 RPM, moderate mode at 1220 RPM and at maximum rotation speed of 2040 RPM. We are going to talk more about fan installation in the next part of our article devoted to cooling efficiency tests.

 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 ]

Discussion

Comments currently: 10
Discussion started: 11/29/09 03:25:23 AM
Latest comment: 12/11/09 08:52:56 PM

View comments

Add your Comment