Articles: Cooling
 

Bookmark and Share

(0) 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 ]

Technical Specifications and Recommended Pricing

Testbed and Methods

We are going to test the cooling efficiency of the new coolers and their today’s competitors in the following testbed:

  • Mainboard: ASUS P6T Deluxe (Intel X58 Express, LGA 1366, BIOS 2101);
  • Processor: Intel Core i7-920, 2.67 GHz, 1.25 V, 4 x 256 KB L2, 8MB L3 (Bloomfield, C0);
  • Thermal interface: Arctic Cooling MX-2;
  • Graphics card: ATI Radeon HD 5850 1 GB GDDR5, 725/4000 MHz;
  • Memory: DDR3 3x2 GB Wintec AMPX 3AXH1600C8WS6GT (Spec: 1600  MHz / 8-8-8-24 / 1.65 V);
  • System drive: OCZ Agility EX SSD (SATA-II, 60 GB, SLC, Indillinx, firmware v1.31);
  • HDD for games and programs: Western Digital VelociRaptor (SATA-II, 300 GB storage capacity, 10,000 RPM, 16 MB cache, NCQ) inside Scythe Quiet Drive 3.5” silencer and cooler chassis;
  • Backup HDD: Western Digital Caviar Green WD10EADS (SATA-II, 1000 GB, 5400 RPM, 32 MB, NCQ);
  • System case: Antec Twelve Hundred (front panel: three Noiseblocker NB-Multiframe S-Series MF12-S1 fans at 900 RPM; back panel: two Scythe SlipStream 120 fans at 900 RPM; top panel: standard 200 mm fan at 400 RPM);
  • Control and monitoring panel: Zalman ZM-MFC2;
  • Power supply: Zalman ZM1000-HP 1000 W (with a default 140 mm fan).

Processor overclocking was limited by the least efficient cooler of our today’s testing participants in its quiet mode. As a result, we managed to overclock our quad-core processor (with polished heat-spreader) with the multiplier set at 21x and “Load-Line Calibration” enabled to 3.84 GHz. The nominal processor Vcore was increased to 1.325 V in the mainboard BIOS:

The memory voltage was at 1.64 V and its frequency was around 1.45 GHz (7-7-7-14_1T timings). All other parameters available in the mainboard BIOS and connected with CPU or memory overclocking remained unchanged.

All tests were performed under Windows 7 Ultimate RTM x64 operating system. We used the following software during our test session:

  • Linpack 64-bit with LinX shell version 0.6.4 – to create maximum CPU load (5 Linpack runs in each cycle with 4096 MB RAM capacity involved);
  • CPU-Z 1.54 – to monitor processor core voltage and frequency;
  • Real Temp 3.58 – to monitor the processor core temperature;
  • Everest 5.30.2109 Beta – to monitor default fans rotation speeds.

So, the complete screenshot during the test session looks as follows:

The CPU was loaded with two consecutive Linpack test runs with the settings as indicated above. The stabilization period for the CPU temperature between the two test cycles was about 8-10 minutes. We took the maximum temperature of the hottest CPU core for the results charts. Moreover, we will also provide a table with the temperature readings for all cores including their average values. The ambient temperature was checked next to the system case with an electronic thermometer with 0.1 °C precision that allows monitoring the temperature changes over the past 6 hours. It was pretty warm already, but the AC wasn’t working yet, so the room temperature during our test session varied between 25.9-26.1 °C.

The noise level of each cooler was measured between 1:00 and 3:00 AM in a closed room about 20 m2 big using CENTER-321 electronic noise meter. The noise level for each cooler was tested outside the system case when the only noise sources in the lab were the cooler and its fan. The noise meter was installed on a tripod and was always at a 200 mm distance from the cooler fan rotor. The tested cooling systems were placed at the edge of the desk on a sheet of polyurethane foam. The lowest noise reading our noise meter device can register is 29.8 dBA and the subjectively comfortable noise level in these testing conditions was around 34 dBA (do not mix it up with low noise level). The fan(s) rotation speed was adjusted in the entire supported range using the new controller revision by changing the voltage with 0.5 V increment.

Besides the default fans, Zalman and Zaward coolers were also tested with one and two Thermalright TR-FDB fans at 1100 and 2050 RPM installed onto the heatsink for air intake and exhaust. Moreover, we will also include the results of the ultimate winner and our today’s performance leader – Noctua NH-D14 equipped with two 140 mm Noctua NF-P14 fans:

In this case the super-cooler costs almost twice as much as Zalman CNPS 10X Performa or Zaward Vapor120, so we also added the results for Zalman CNPS10X Flex, Performa’s predecessor, and Alpenföhn Nordwand, which is practically the today’s best cooler with heatpipe direct touch technology.

 
Pages: [ 1 | 2 | 3 | 4 | 5 | 6 | 7 ]

Discussion

Comments currently: 0

Add your Comment